SBORNÍK vědeckých prací
Vysoké školy báňské - Technické univerzity Ostrava,
Řada strojní
TRANSACTIONS
of the VŠB - Technical University of Ostrava,
Mechanical Series
ISSN 1210-0471 (Print)
ISSN 1804-0993 (Online)
ISSN-L 1210-0471
DOI: 10.22223/tr.2013-2
- Table of contents
Michał BARCIKOWSKI, Wacław KRÓLIKOWSKI
Characteristics of Impact Damage and Post-Impact Strength in Glass-Fibre-Reinforced Plastics with Different Reinforcement Architecture
DOI: 10.22223/tr.2013-2/1951Matěj BARTECKÝ
Finite Element Analysis of Membrane of Automotive Key
DOI: 10.22223/tr.2013-2/1952Sándor BODZÁS, Illés DUDÁS
Comparative Finite Element Method Analysis of Spiroid Worm Gear Drives Having Arched Profile and Having Linear Profile in Axial Section
DOI: 10.22223/tr.2013-2/1953Radek ČADA, Jan ZLÁMALÍK
Project of Economically Profitable Technological Process of Production of Rotor and Stator Plates of Inductive Position Sensor by Blanking and Roll Bending
DOI: 10.22223/tr.2013-2/1954Josef DOBEŠ, Milada KOZUBKOVÁ
Modelling of Cavitation of Wash-Out Water, Ammonia Water, Ammonia Water with Increased Content Ammonia and Hydrogen Sulphide, Tar Condensate
DOI: 10.22223/tr.2013-2/1955František FOJTÍK
Application of Selected Multi-axial Fatigue Criteria Are Using Fifth-dimensional Space on the Results of Fatigue Experiments
DOI: 10.22223/tr.2013-2/1956Marek GEBAUER, Jan SZWEDA
Simulation of Welding of Thin-Walled Pipe
DOI: 10.22223/tr.2013-2/1957Vladimír GOGA
Finite Element Model of the Strain Gauge For Determining Uniaxial Tension
DOI: 10.22223/tr.2013-2/1958Wiktor HUDY
Analysis of Parametric Optimization of Field-Oriented Control of 3-Phase Induction Motor with Using Evolutionary Algorithm
DOI: 10.22223/tr.2013-2/1959Pawel JURECZKO, Damian GĄSIOREK, Michal BACHORZ, Lukasz JUSZYŃSKI
Prototype Multifunctional Device for Contraction Exercises of Joints and Muscles of the Lower Limb
DOI: 10.22223/tr.2013-2/1960Richard KLUČKA, Luboš PEČENKA, Jana PRZECZKOVÁ, Karel FRYDRÝŠEK
Numerical Calculation of Overpressure and Underpressure of Reservoir Z2
DOI: 10.22223/tr.2013-2/1961Miloš MADIĆ, Miroslav RADOVANOVIĆ, Marin GOSTIMIROVIĆ
Selection of Near Optimal Laser Cutting Parameters in CO2 Laser Cutting by the Taguchi Method
DOI: 10.22223/tr.2013-2/1962Lucie MALÍKOVÁ, Václav VESELÝ
Williams Expansion Terms and their Importance for Accurate Stress Field Description in Specimens with a Crack
DOI: 10.22223/tr.2013-2/1963Ondřej MAREK, Aleš BÍLKOVSKÝ, Petr JIRÁSKO
Simulation Model of the Weaving Machine "Camel” and Selection of the Sufficient Driving Motor
DOI: 10.22223/tr.2013-2/1964Martin MARIŠKA, Petr DOLEŽEL
Piecewise-Linear Neural Network – Possible Training Algorithms Efficiency Comparison
DOI: 10.22223/tr.2013-2/1965Marcel MORE, Ondrej LÍŠKA
Recognition of Gestures using Artifical Neural Network
DOI: 10.22223/tr.2013-2/1966Marek NIKODÝM, Karel FRYDRÝŠEK
About Central Difference Method Applied for the Beams on Elastic Foundation
DOI: 10.22223/tr.2013-2/1967Zdeněk NOVÁK, Martin NOVÁK, Jan CHYSKÝ
Measuring Hysteresis Loop and Optimization of the Stator Tooth Width in the Permanent Magnet Synchronous Machine
DOI: 10.22223/tr.2013-2/1968Stanislav SEITL, Jan KLUSÁK, Pelayo FERNANDEZ, Alfonso CANTELI
Comparison of Analysis Methods of Data from Thermographic Measurements of Al 2024 Fatigue Limit For R=0.1
DOI: 10.22223/tr.2013-2/1969Irina SEMENOVA, Petr HORYL
The Influence of the Basic Parameters of the Numerical Model on the Contact Pressure in Dynamic Tasks
DOI: 10.22223/tr.2013-2/1970Ján VACHÁLEK, Michal BARTKO
Online System Identification Method Using Modified Regularized Exponential Forgetting
DOI: 10.22223/tr.2013-2/1971